The new Easyboot Fury Glue-On is a longer glue-on shell that comes with a slot to accommodate different cushion densities to soften or stiffen the heel area of the boot. The shell length is trimmable to customize the level of support.
A Fury Fit Kit is recommended to determine proper sizing for the Easyboot Fury Glue-On.
Easyboot Fury Size Chart | ||
Size |
Width in mm |
Length in mm |
0 |
104-109mm |
102-120mm |
0.5 |
108-113mm |
108-125mm |
1 |
112-117mm |
112-130mm |
1.5 |
116-121mm |
116-135mm |
2 |
120-125mm |
120-140mm |
2.5 |
124-129mm |
124-145mm |
3 |
128-133mm |
128-150mm |
3.5 |
132-137mm |
132-155mm |
4 |
136-140mm |
136-160mm |
Q How do I measure?
A Measuring information can be found on the Easyboot Fury Glue-On sizing page. Ideally, your horse should fit into the same size on the chart for both width and length.
Q What is the difference between the Easyboot Fury Glue-On and Easyboot Glue-on?
A The Easyboot Fury Glue-On is a longer shell that can add additional heel support. The heel is open on the Easyboot Fury Glue-On and closed on an Easyboot Glue-On. The Easyboot Fury Glue-On has a more aggressive tread and a slot that accepts an EVA heel pad.
Q If my horse wears a size 1 Easyboot, what is the comparable size?
A The sizing for the Fury Glue-On is completely different than our other boots. You will need to re-measure your horse in millimeters and look at the size chart. Glue-On boots come in both whole and half sizes.
Q How do I determine the correct size boot and what is a Fit Kit?
A To ensure you purchase the correct size, we recommend that you order a Fit Kit. The Fury Kit comes with three boots—the size you think you need and a half size on either side. There are complete instructions and photos showing how the boot should fit. To order a Fit Kit or learn more, click here (link to the Fit Kit page)
Q How do I know what size Fit Kit to order?
A A Fit Kit gives you the size you think you need plus a half size on either side. Measure your horse after a fresh trim and look at the size chart for the Fury. You will want to go by your horse’s width. If your horse measures a size #1.5 in width you will need to order a size #1.5 Fit Kit. This will give you a size #1, a #1.5 and a #2 boot.
Q What if I am more than one size apart?
A Purchase the size that corresponds to the width. The extra length can be removed with a belt sander, nippers or rasp.
Q What is involved in the process of applying an Easyboot Fury Glue-On?
A You can download the Glue-On application guide in PDF format, or visit the Glue-On fitting page for instructional videos. You will need additional accessories including Vettec Adhere, Vettec mixing tips, Vettec glue gun, gloves, a rasp, and a heat gun.
Q What adhesive do you use?
A Vettec Adhere and Sikaflex 227
Q Where can I find a heat gun?
A EasyCare does not sell heat guns. However, affordable heat guns can be found at most hardware stores.
Q How long can you keep the boots on?
A We recommend no longer than 5 days in a wet environment and 10 days in a dry environment.
Q What if my horse needs a different size boot for every foot?
A Because the sizing is so precise, it is possible that there will be horses with different sizes for each foot. Again, your best bet is to order a Fit Kit so you can double-check your measurements.
Q How many uses will I get out of the boots?
A Generally, you will only get one use out of your boots, unless you diligently remove all the glue after use. We recommend using a circular wire brush on a drill press.
Q What's the process to remove Easyboot Fury Glue-On shells?
A Video instructions can be found on the Easyboot Fury Glue-On fitting page.
Q Are Glue-On's legal for competitive trail rides (CTRs)?
A Yes.